GE Monogram Beverage Dispenser Wine Chiller Wine Reserve and Beverage Center User Manual

Installation  
Instructions  
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com  
Wine Chiller,  
Wine Reserve  
and  
Beverage Center  
Design Guide  
With Installation Instructions  
 
Design Guide  
THE INSTALLATION SPACE  
PRODUCT CLEARANCES  
The wine chiller, wine reserve and beverage center is  
factory set for a 110° door swing.  
Locate  
Outlet  
When installed in a corner:  
• Allow 4min. clearance on the hinge side for the  
90° door swing and to allow racks to slide out.  
• Allow 10minimum clearance on the hinge side  
10-1/2"  
24"  
9" Max.  
34-1/2"-35"  
for a full 110° door swing.  
1-1/2"  
23-3/4" Min.  
90° Door Swing  
23-3/4"  
10" Minimum  
to Wall  
21-5/8"  
NOTE:  
Handle and  
34-1/2"  
handle standoff  
depth is 1-3/4″  
23-5/8"  
90°  
23-3/4"  
4" Minimum  
The cutout depth should be 24″  
110°  
to Wall  
The cutout dimensions shown allow for a full door  
swing and access to the pull-out racks when installed  
as a built-in in standard 24deep cabinets.  
• The wine chiller, wine reserve and beverage center  
can be installed freestanding.  
• The door swing is reversible on all models. If  
desired, change the door swing before installation.  
Choose the location:  
• These products may be closed in on the top and  
three sides as long as the front is unobstructed for  
air circulation and proper access to the door.  
• Do not install these products where the temperature  
will go below 55°F (13°C) or above 90°F (32°C).  
• Do not install where it will be subject to direct  
sunlight, heat or moisture.  
• If installing between frameless cabinets, a 1/2wide  
filler strip or side panel may be needed on hinge  
side. The filler strip will act as a spacer between the  
case and adjacent cabinet door swing. The width  
of the opening must include the filler panels.  
NOTE: The door should protrude 1beyond the  
surrounding cabinets.  
• These products are not designed to be stacked one  
over the other.  
Additional Specifications  
• A 120 volt 60Hz., 15 or 20 amp power supply is  
required. An individual properly grounded branch  
circuit or circuit breaker is recommended. Install a  
properly grounded 3-prong electrical receptacle  
recessed into the back wall as shown. Electrical must  
be located on rear wall as shown. NOTE: GFI  
(ground fault interrupter) is not recommended.  
Black or Stainless Steel Toekick Options  
• These products are shipped with a black toekick  
installed. An optional stainless steel toekick is also  
supplied with each product. For shipping purposes,  
the stainless steel toekick is secured to the back  
of the unit.  
SIDE-BY-SIDE INSTALLATIONS  
Increase storage capacity by installing two Monogram  
beverage centers, wine chillers or wine reserves together.  
Or, for a complete refreshment center, install any two  
of these units together.  
• A side-by-side installation requires at least a 47-1/2″  
wide opening. No trim kits required.  
Locate  
Outlet  
10-1/2"  
10-1/2"  
24"  
14"  
34-1/2"-35"  
9" 9"  
15"  
1-1/2"  
• Products must operate from separate, properly  
grounded receptacles.  
47-1/2" Min.  
3
 
Installation Instructions  
TOOLS REQUIRED  
STAINING WOOD DRAWER FRONTS  
• #2 Phillips screwdriver  
• Adjustable wrench  
The drawer fronts are unfinished cherry wood.  
During use, oil from hands may accumulate and stain  
the wood.  
• The drawer fronts may be stained and sealed to  
match adjacent cabinetry. The tinted glass will  
make the stained wood appear darker. A true color  
match can be seen only when the door is opened.  
• Apply the stain and sealer according to the  
manufacturer’s instructions. To avoid unpleasant  
odor, keep the door open to ventilate and allow  
the stain/sealer to dry completely before using  
the product.  
PARTS SUPPLIED  
• Monogram nameplate  
• Hardware for changing door swing  
• Optional stainless steel toekick with screws  
and spacers  
• Left and right side hinge covers  
• Top screw hole cover  
GROUNDING THE WINE CHILLER,  
WINE RESERVE AND BEVERAGE  
CENTER  
STEP 1 REMOVE PACKAGING  
• Remove corner blocks and foam drawer stops.  
• Remove all packing material, tape and protective  
plastic coverings.  
• Remove stainless steel toekick taped to the back  
of the unit.  
IMPORTANT –  
FOR PERSONAL SAFETY, THIS APPLIANCE MUST  
BE PROPERLY GROUNDED.  
Please read carefully.  
The power cord of this appliance is equipped with a  
three-prong (grounding) plug which mates with a  
standard three-prong (grounding) wall receptacle to  
minimize the possibility of electric shock hazard from  
this appliance.  
CAUTION:  
Small objects are a choke  
hazard for children. Remove and discard any parts  
not used.  
MISE EN GARDE :  
Les petits  
objets peuvent étrangler les enfants. Il faut jeter  
Have the wall outlet and circuit checked by a qualified  
electrician to make sure the outlet is properly grounded.  
toutes les piéces qui ne sont pas utilisées.  
Where a standard 2-prong wall outlet is encountered,  
it is your personal responsibility and obligation to  
have it replaced with a properly grounded 3-prong  
wall outlet.  
DO NOT, UNDER ANY  
CIRCUMSTANCES, CUT  
OR REMOVE THE THIRD  
(GROUND) PRONG  
FROM THE POWER CORD.  
DO NOT USE AN ADAPTER PLUG TO CONNECT  
THE REFRIGERATOR TO A 2-PRONG OUTLET.  
DO NOT USE AN EXTENSION CORD WITH THIS  
APPLIANCE.  
4
 
Installation Instructions  
STEP 2 REVERSE DOOR SWING  
SKIP THIS STEP IF DOOR SWING SUITS THE  
INSTALLATION  
Install  
3 Hinge  
Screws  
Parts Included:  
• Top left case hinge  
Remove  
Top Hinge  
• Bottom left case hinge  
• Left and right side decorative hinge cover  
• Decorative hinge screw hole cover  
• Torx® driver bit  
Hinge  
Pin and  
Bracket  
Tools Required:  
• Phillips screwdriver  
• Electric drill  
Door Stop  
and Cam Riser  
Remove the door:  
• Flatten the shipping carton to use as a pad.  
• Remove the 2 screws and the toekick. Set aside the  
screws and toekick for final installation.  
• Use the supplied Torx® bit and electric drill to  
remove the 3 screws holding the top case hinge.  
Lift off the hinge. (Screws will be used to install the  
new hinge.)  
Remove  
Hinge  
• Lift the door off the bottom case hinge.  
• Remove the bottom case hinge pin and bracket.  
Apply Monogram Nameplate:  
• Install the Monogram nameplate. See instructions  
and template on back cover.  
Rotate the door:  
The handle will be on the right side of the door;  
hinges will be installed on the left side of the case.  
• Remove the door stop and cam riser on the original  
bottom right side of the door.  
• Remove the fill plug on the top right side  
of the door.  
Install Toekick  
The toekick has a  
cutout on the  
left and right  
sides.  
Remove  
the plug  
• Turn the door over and reinstall the fill plug on the  
new left side.  
Move Fill  
on the left  
side and  
Plug to  
Reinstall the door:  
• Install the original door stop and cam riser onto  
the bottom left side of the door.  
Right Side  
reinstall on  
the right  
side. If you  
choose to install  
• Install the new supplied bottom case hinge pin and  
bracket onto bottom left side.  
the stainless steel toekick,  
• Place the door onto the bottom case hinge.  
• Install the supplied left-hand top case hinge with  
the 3 original screws.  
• Select the hinge cover marked with an “L”.  
• Peel backing off the tape inside the decorative  
reinstall the plug on the right side of that toekick.  
• Install original screws and spacers or screws and  
spacers supplied with the stainless steel toekick.  
Install screws through the spacer standoff, toekick  
and into the base as shown.  
hinge cover.  
• Press and snap the hinge  
Install Covers  
cover into place.  
• Snap the screw hole cover into  
place on the opposite side.  
IMPORTANT:  
Check to be sure screws are tight and that the door  
is straight and does not sag. The door should swing  
freely.  
5
 
Installation Instructions  
STEP 3 LEVEL  
STEP 5 SLIDE PRODUCT INTO  
THE CUTOUT  
• Use an adjustable wrench to turn the leveling legs  
and raise or lower the product.  
• Carefully, slide the unit into the opening.  
Be careful not to entangle power cord.  
• Make certain that the door protrudes 1beyond  
the surrounding cabinets.  
• Adjust carefully; the product should be level and  
plumb with cabinetry, and should align with adjacent  
toekick height.  
• Check again to be sure the unit is level.  
STEP 6 INSTALL NAMEPLATE  
• Follow instructions on the back page for installation  
of the Monogram nameplate.  
STEP 7 SET TEMPERATURE  
CONTROLS  
Turn Right to Lower  
Turn Left to Raise  
• The temperature controls are preset. Refer to  
the Owner’s Manual for more information.  
Allow 24 hours for temperature to stabilize.  
If you skipped Step 2:  
• Select the hinge cover marked “R” or “L”, depending  
on door swing.  
• Peel backing off the tape inside the decorative  
hinge cover. Press and snap into position.  
• Snap the screw hole cover into place on the  
opposite side.  
STEP 4 CONNECT POWER  
• Connect power cord plug to a properly grounded  
receptacle.  
• Check to make sure power is on by opening the door  
to see if interior light turns on.  
6
 
7
 
TEMPLATE FOR NAMEPLATE LOCATION  
Cut on Dotted Line  
Upper Left  
Upper Right  
Corner of  
Glass if Hinge  
is on Right  
Top of Glass Door  
Corner of  
Glass if Hinge  
is on Left  
Top of Badge  
Door Frame Side  
Door Frame Side  
DOOR NAMEPLATE LOCATION  
To position nameplate:  
• Cut template along dotted line.  
• Hold or tape template behind  
glass door so that it is visible from  
the front side.  
• Remove backing from nameplate.  
• Place nameplate onto front side of  
door, matching illustration on the  
template.  
IMPORTANT: Nameplate must  
be placed on the opposite side of  
the door handle.  
Note: While performing installations described in this book,  
safety glasses or goggles should be worn.  
For Monogram® local service in your area, call  
1.800.444.1845.  
Note: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
Pub. No. 49-60210-4  
Dwg. No. 197D5129P001  
03-04 JR  
Printed in Slovenia  
 

Edimax Technology Network Router BR 6641 User Manual
Essick Air Humidifier EA1208 User Manual
Fisher Paykel Ventilation Hood 87641 User Manual
Frigidaire Washer Dryer FEX831F User Manual
Gaggia Espresso Maker 12300 8002 User Manual
GE Blender 169202 User Manual
Gemini Speaker RS 308 User Manual
GE Trash Compactor GCG1500LBB User Manual
Gianni Industries Door GL 1200F User Manual
Gitzo Camcorder Accessories G1197 User Manual